Sign In | Join Free | My chinacsw.com
chinacsw.com
shenzhen faith trading limited
shenzhen faith trading limited
Home > Dental Handpieces >

High Speed Air Turbine Handpiece/Japan Panamax Handpiece

High Speed Air Turbine Handpiece/Japan Panamax Handpiece

Payment Terms : T/T, Western Union, MoneyGram
Contact Now

High Speed Air Turbine Handpiece/Japan Panamax Handpiece


PANA MAX is the first turbine launched to the world marketplace. The turbine was among the first that featured capsulated cartridges and rated very high for its powerful torque, low noise and extreme durability. PANA MAX, the latest of PANA AIR series, comes with a number of improvements including more hygiene-conscious body design and autoclavability at up to 135°C.

Dental High Speed Handpiece PANA-MAX of Push Button Model.
1.Product Features
-Ultra Push Chuck – Simple yet secure fastening
-Single Water Spray – Efficient cooling
-Ergo Grip – Secure grip for your confidence
-Replacement Cartridge

2.Specification
Wrench type; Push button type;
2-hole; 4-hole;
Standard head; Torque head; Mini head;

With quick coupling


3.Characteristics

1> 2-Hole or 4-Hole Available, without quick coupling
2> Rotational speed≥400 000 rpm
3> operating air pressure: 1.8-2.2kgf/cm2
4> Single water spray
5> head diameter: Ø 10.2
6> chuck type: push button type

7>Stainless Steel Body


ModelPana Max push button handpiece
Hole2 or 4 hole
Ratational speed≥400 000 rpm
Water spraysingle water spray
Chuck typepush button
HeadStandard or Torque head
Warranty6 months

Dental handpieces right use way:
1. The need to use a clean , dry , oil-free air compressors for medical use ;
2. The air pressure between 2.3-2.8kgf / cm2;
3. Place the adapter with quick connector at the bottom of a combination of dental handpieces , and confirm that the card lock fixed ;
4. Press the pedal , handpiece operation and examine whether the normal operation of the spray head . If everything is normal, you can start using the handpiece .


After each patient use , maintenance should be done as follows
1. First remove the diamond burs , and clean up all the teeth on dental handpieces precipitate ;
2. Use a metal needle to clean the spray holes and fumaroles ;
Note: The spray holes and diamond burs into 40 -degree angle , fumaroles and diamond burs to a 30 degree angle.
3. Place the clean lubricating oil is sprayed into the axial hole 1-2 seconds ( diamond burs is plugged holes ) ;

4. In the bottom of the handpiece were ( with / without quick connector ) two kinds of styling , make the right amount of lubricant is injected into the bottom ;
5. The handpiece with quick connector combination ( first determine the water switch is turned off )
6. Replace the diamond burs , surrounded by white silk cloth handpiece head ( make sure the needle does not touch the diamond burs and white gauze , so as not to tie ) ;
7. pedal depressed for about 20 seconds , look at whether there is in white gauze on any stain. If there are stains on the white gauze , again, add oil , starting from item 4 continued routine maintenance , know that white gauze until no stain ;
8. Finally, no more than 135 degrees Celsius temperature and high pressure sterilization.


Handpiece routine maintenance
Fault: the occurrence of undesirable phenomena water
( 1 ) inadequate water supply .
( 2 ) the amount of water is not uniform.
( 3 ) is not a mist of water .
( 4 ) no water completely .


Solution: Check the water blocked the site
( 1 ) pipeline : the turbines removed to check for the amount of water flowing from the pipeline . If there is no water out, it may be pipes or water treatment units system problems ( bad or wrong operation , there is not enough water pressure ) .


( 2 ) interface : the interface conductors commissioning . Without the right amount of water flowing out , it indicates a problem at the interface ( such as clogged scale water supply systems or interface loose , resulting in insufficient pressure ) .
( 3) The body of the phone : the shaft from the turbine to remove , install interface running on . If there is no outflow amount of water, it is the problem turbines within the body ( water holes or dirt clogging turbines within the water supply system clogging ) .
( 4 ) shaft : If the above three normal outflow of water , it is the axis of the core problem (water nozzle clogging ) .


Axis core spray nozzle clogging .
Solution:

( 1 ) remove the end cap , remove the spool core .
( 2 ) the brush behind the nozzle cleaning needle is removed , insert the needle straight spout .
( 3 ) nozzle cleaning needle to be inserted into the upper section of the trench ( bur through jet slot ) at the till . Part of this special brush with dust brush clean.
( 4 ) the use of three guns and other bur blowing from the side .
(5 ) mounted on the shaft head , be sure to properly install the 0 -ring .


bur easy to fall off , bur not pull it out , the axis vibration.
Solution:

(1 ) Select the bur , bur must confirm the allowable speed range specified by the manufacturer , or else when the cutting load is greater than the chuck clamping force bur easily.
( 2 ) mini- head bur should use a short handle , easy to fall off when attached to the shank burs .
( 3 ) Do not use worn tapered bur , curved bur bur missing edge , otherwise it will affect the durability of the bearing Must be drawn .


(4 ) installation bur bur confirm indeed firmly installed , if not into the depths of shallow plug can cause dangerous bur flying .



China Customized Inflatable Bumper Ball Game Bubble Adult Grass CE supplier

High Speed Air Turbine Handpiece/Japan Panamax Handpiece Images

Inquiry Cart 0
Send your message to this supplier
 
From:
To: shenzhen faith trading limited
Subject:
Message:
Characters Remaining: (0/3000)
 
Inquiry Cart 0